-
STUB AXLE ASSEMBLY - SERIES 3 109"
1 × $97.63 -
Tie Rod End, Steering Rack
1 × $16.83 -
Exhaust System, Twin Box Type
1 × $154.00 -
Cylinder Head Stud, Long 14cm Genuine New Old Stock
3 × $9.55 -
Bearing, 1st Motion Shaft
2 × $12.00 -
Bump Stop, Front Upper
1 × $11.39 -
Revive Starter Kit
2 × $104.50 -
Apron Panel Adaptor R/H, later grille panel to early type
1 × $64.46 -
BRAKE SHOE RETURN SPRING, 10" BRAKES (RED)
2 × $6.33 -
Valve Guide
2 × $7.70 -
Boot Kit, Pot Joint, Inboard CV
2 × $11.50 -
HT Lead Ignition Spark Tester
1 × $49.50 -
Heater Tap
1 × $44.00 -
Cylinder Head Nut, Plain
2 × $2.81 -
Brake Pipe Bender
2 × $45.93 -
Brake Hose Kit, Front & Rear, Disc Brake
1 × $68.20 -
Sensor, Oxygen Lambda LH
2 × $119.74 -
AIR TO COIL CONVERSION KIT +2" MEDIUM - DISCOVERY 2
2 × $1,133.00 -
Bush, Diff Side Cover
1 × $35.20 -
Valve Cotter, Pair
1 × $9.90 -
SHOCK ABSORBER- REAR - ALL TERRAIN
1 × $104.50 -
By-pass Hose, Standard
1 × $5.94 -
OIL COOLER - ENGINE 5.0LTR S/C
1 × $227.15 -
Thermostat Housing Stud, 52 mm
2 × $2.86 -
Accelerator Cable, Rover Mini, Multi Point Injection
1 × $53.74
Shop
-
-
$34.65
Accelerator Cable, Rover Mini Single Point Injection
Suits Mini 1990 on with the 1275cc engine.
-
-
-
-
$36.25
Accelerator Pedal, Wider Type
This type of pedal was fitted to the Rover Mini and can be fitted to any Australian Mini
-
$53.35
Valve block & seals for brake accumulator.
Suit Jaguar XJ40 up to 594575
Genuine Jaguar New Old Stock
-
-
$1,798.50
The acoustic mat system has been designed to drastically reduce noise entering the cabin of your Land Rover. Made from cast dense polyurethane, the mat is built to industrial standards for reducing noise levels often found in construction equipment. It provides a hard wearing, durable surface that can withstand constant daily use and is easy to clean. A custom fit mat drastically reduces noise entering the cabin and panel reverberation.
[envira-gallery id="91428"]PLEASE EMAIL TO PRE-ORDER – CONTACT BMI
-
-
-
-
$7.92
Adaptor Between Carburettor & Air Cleaner, 1 1/4″ SU. This is a 2nd Hand part in good condition.
-
$16.78
Adaptor Fuel Bowl To Carby  L/Hand 30 Degree
This is the buffer that goes on some carbys (mainly twins) between the fuel bowl and the carby body, there is a L/H and a R/H this rubber has the cut at about 1 o’clock position.
-
$16.78
Adaptor Fuel Bowl To Carby R/Hand 30 Degree
This is the buffer that goes on some carbys (mainly twins) between the fuel bowl and the carby body, there is a L/H and a R/H this rubber has the cut at about ’11 o’clock position.