-
THERMOSTAT & WATER HOUSING
1 × $95.48 -
Valve Cotter, Pair
2 × $9.90 -
Shake Proof Washer, Steering Wheel To Column
1 × $0.33 -
THERMOSTAT 4.4L V8
1 × $48.13 -
INTERCOOLER SILICONE HOSE KIT TDV6 2.7L
1 × $143.00 -
Brake Fail Switch
1 × $79.75 -
Thermostat Housing Stud 48mm (1.9375") Long
1 × $2.82 -
Diesel Injector Extractor - for JLR 2.7, 3.6 engines
1 × $217.25 -
FRONT ARM, 3 DEG 44mm CASTER CORRECTED, H/D
2 × $495.83 -
Wheel Nut, Rostyle
1 × $4.68 -
STARTER MOTOR - D3/RRS AJV8
1 × $340.56 -
Nut, 3/16'' UNF, Multi Use
1 × $0.39 -
Rocker Arm / Tappet
1 × $38.50 -
Wheel Nut, Rostyle Wheels, Mini ''S'' 2/H
1 × $2.20 -
MIRROR ARM, EXTRA LONG
1 × $83.33 -
Adjustable Brake Caliper Rewind Tool Kit
2 × $105.33 -
GREASEABLE BALL JOINT, A FRAME
3 × $41.42 -
Bolt, Front Sub Frame Tower to Body, (Dry)
2 × $13.20 -
AIR FILTER, D4/D5/RANGE ROVER
2 × $19.64 -
Rotor Arm, Suit Ducellier Distributor
1 × $5.50 -
Master Cylinder Tank, Plastic
2 × $44.00 -
Motor & Pump, Windscreen Washer
2 × $42.63 -
HT Lead Ignition Spark Tester
1 × $49.50 -
A/C CONDENSER w/DRYER - D4/RRS
2 × $262.96 -
PUMP - OIL
1 × $210.93 -
HEADLAMP RETAINING RIM, INNER 7"
2 × $22.83 -
Exhaust Clamp, Manifold to Engine Pipe Quick fit
2 × $11.83 -
Fuel Injector Remover - for JLR
2 × $225.23 -
WEAR SENSOR, FRONT BRAKES, RR, RRS, D5
2 × $14.32 -
Steering Rack Wave Washer
1 × $1.65 -
Heater Tap & Blanking Plate Gasket
2 × $0.66 -
Blanking Plug, Various Uses
2 × $4.24 -
Temperature Transmitter
1 × $16.50 -
Apron Panel, no mounts, Mini Aftermarket
1 × $342.65 -
Wheel Spacers & Studs, 3/4" 19.0 mm Thick
1 × $63.80 -
Ball Joint Kit, Genuine Rover Brand
1 × $94.12
Suspension
- View cart You cannot add that amount to the cart — we have 1 in stock and you already have 1 in your cart.
-
$209.00
Adjustable Front Lower Arm Kit (Pair)
One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required.
Sold in pairs only.
-
-
-
-
$37.40
Ball Foot & Cup Assembly, Front only
Built in 4.33mm Spacer
-
-
-
-
-
Availability: This product is currently out of stock.
Ball Joint Separator – Cup Type
Carbon Steel
Thrust nut for leverage
Jaws : 22mm W – 20mm D – 50mm opening -
$8.95
Idler Gear Bearing, 1.004″ OD
Upper Control Arm Bearing, Front Suspension
The 25.4mm wide original genuine bearing to take 19.05mm size idler gear shaft and sits in the gearbox case on early 3 synchro types and also in the early type clutch case.
-
$13.20
Bolt, Front S/Frame Tower to Body, (Dry)
Upper Control Arm Use with # 21A2694 Spacer
-
$9.52
Bolt, Mount Bracket, Engine & Radiator
Also Front Tower Bolts Hydrolastic Front Subframe
-
$3.52
Tie Bar to Lower Arm Bolt. 5/16″unf by 1.3/8″long.
Original Bolt with a special length shank for the front suspension tie bar to the lower arm. Always check this out for any signs of wear and replace accordingly.
BH605141 is the exact correct length shank but slightly longer thread if required
-