-
Twin Carb Choke Link Shaft, Cooper-S
1 × $24.39 -
HUB NUT SPANNER 52mm
2 × $11.00 -
OLIVE, M8
2 × $1.65 -
Starter Switch Push
3 × $86.90 -
Nut, 3/16'' UNF, Multi Use
1 × $0.39 -
BRAKE SHOE KIT - XJ40
2 × $68.75 -
Screw, 1/4" x 5/8" Countersunk
1 × $1.60 -
Coupling, Steering - D3/D4/RRS
2 × $231.00 -
Throttle Shaft Bush, HS4 1-1/4"
1 × $10.45 -
Throttle Shaft, Carburettor, 1 1/2" SU
1 × $32.56 -
BUSH, PANHARD ROD
1 × $9.63 -
Mini Kingdom Online Parts Catalogue
1 × $59.95 -
Gasket, Cylinder Head, Standard
1 × $16.50 -
Ignition Coil
1 × $89.32 -
Engine / Gearbox Mount
1 × $192.50 -
TIE ROD END, STEERING 14mm
2 × $53.63 -
LAMBDA/O2 SENSOR ASSY, FRONT/UPSTREAM - V6/V8
2 × $155.93 -
Twin Carburettor Linkage Kit
1 × $104.50 -
BALL JOINT, A FRAME. ADJUSTABLE & GREASEABLE
1 × $51.70 -
Tool For Wheel Cylinder Clip
1 × $40.70 -
NUT, ALLOY WHEEL OEM
2 × $9.90 -
GASKET, INLET MANIFOLD (SINGLE)
1 × $17.33 -
CAP, COOLANT EXPANSION TANK - 200kpa
2 × $11.94 -
TURBOCHARGER - 300TDi (Complete Unit)
1 × $1,314.50 -
Idler Pulley Primary Drive
1 × $37.13 -
Alternator Belt
1 × $17.91 -
Rotor Arm, 45D Distributor
2 × $6.60
XJ SERIES I 1968-1973
-
-
-
Availability: This product is currently out of stock.
Crankshaft sprocket for timing chain.
Genuine Jaguar New Old Stock. Suits;
Jaguar E-Type S3 V12 1971 – 1975
XJ12 Series 1, 2, 3 1968 – 1992
XJS V12 1975 – 1996
X300 6.0L 1995 – 1997
-
$82.06
Oil filter for sump on Jaguar XJ6 Series 1, 2 & 3
Genuine Jaguar New Old Stock
-
$99.00
Designed to allow the checking and setting of the crank driven fuel pump camshaft used on the Jaguar Land Rover AJ V8 5.0lt naturally aspirated and supercharged petrol engines, the Laser 7878 is equivalent to the OEM tool but is manufactured in one piece for ease of use. For full details of use, please see vehicle specific OEM data.
-
$2.70
Grease Nipple Multi Use
1/8″ BSP Straight, short.
Front ball joints, front upper control arms, rear suspension trailing arm shaft, propshafts with greasable uni joints.
-
-
-
$121.94
Rear inner wheel bearing
-
$104.50
Voltage Stabiliser for Instrument cluster (dash instruments/clock)
It is a 3 pin stabilizer, please check you have this type and not the 4 pin
-
-
$61.71
Needle & Seat for SU Carburettors, HS2 & HS4
Quantity 2 required
-
Availability: This product is currently out of stock.
Piston Ring Compressor Set
This set enables the installation of piston rings ranging from 73mm to 117mm.
-
-