-
Thermostat Housing
1 × $24.20 -
Bush Front Lower Radius Arm
1 × $45.35 -
Adaptor Between Carburettor & Air Cleaner, 1 1/4" SU 2/Hand
2 × $7.92 -
COIL SPRING - REAR MEDIUM +2"
1 × $363.00 -
Thermostat, 74c, BORG & BECK
2 × $19.58 -
Throttle Shaft, Carburettor, 1 3/4" SU HS6
1 × $23.10 -
Accelerator Cable Connector
2 × $6.38 -
INSULATOR - ENGINE MOUNTING - FREELANDER 2 - RANGE ROVER EVOQUE - DISCOVERY SPORT
1 × $71.61 -
KIT FITTING LWR FR CONTROL ARM PER SIDE
1 × $49.23 -
Emblem, For Gear Knob & Key Fobs, BMC Logo 27.4mm dia
2 × $2.50 -
Dowel, Steering Arm to Swivel Hub
2 × $8.21 -
Coil Ignition
1 × $88.00 -
Fuel Pump Camshaft Alignment Tool - for JLR
1 × $99.00 -
250KG 240V ELECTRIC HOIST
1 × $197.09 -
SWITCH, TAILGATE - FREELANDER 2/RANGE ROVER SPORT
1 × $53.52 -
Clip, Interior Trim
1 × $2.86 -
Brake Light Switch
2 × $8.53 -
Grease Nipple Multi Use
2 × $2.70 -
ALLOY WHEEL NUT, BLACK
1 × $15.13 -
ALTERNATOR - DISC/SPORT GENUINE
2 × $907.50 -
Accelerator Cable, Rover Mini Single Point Injection
2 × $34.65 -
Distributor Cap, Top Entry 23D Lucas
2 × $19.80 -
Long Male Brake Nut 3/8 UNF x 24tpi
2 × $2.42 -
SENSOR, HEIGHT LHR - D3/RRS
1 × $105.05 -
Y Piece Engine Breather Hoses Twin carburettors
1 × $8.25
Fuel System
-
$9.90
A Worn throttle Shaft (spindle) can cause erratic performance and sometimes the housing is worn as well.Â
This bush is used on both sides of the carburettor to repair a worn carburettor body, often required when replacing the throttle shaft (spindle) on the HS4 carburettor.
As a guide the internal diameter is .3125 you may have to ream body to 9.55mm.
-
$10.45
A Worn throttle Shaft (spindle) can cause erratic performance and sometimes the housing is worn as well.Â
This bush is used on both sides of the carburettor to repair a worn HS2 carburettor body, often required when replacing the throttle shaft (spindle) on the carburettor.
Qty 2 required
-
-
-
$8.80
Tube, Air Pre-Heat Duct,Â
Fitted between the air temperature control and # 12G3213
-
$24.39
Twin Carb Choke Link Shaft.
Rod with chamfered ends about 57.2mm long (shorten to 54mm for twin HS4) which has AUE586 and AUE587 clamps to fit between SU twin carbs for the linkage.
-
$104.50
Twin Carburettor Linkage Kit
This kit will suit all the later 1.25″ and 1.5″ twin carb set ups where the balance rods between the carbs are equal in length (2.25″) Some early model carbs had the balance bar with a triangular plate, this is a shorter length.
-
$1.10
Wing Nut, Air Filter To Carburettor 1- 1/4″ SU
This a replacement wing nut to suit the air filter lid on the single HS2.
-
$69.03
Workshop Manual, Moke 1971Â to 1982 Gregorys
-