-
Fuel Pump Camshaft Alignment Tool - for JLR
1 × $99.00 -
Brake Spanner 1/4" Sq x 5/16" OE
2 × $28.33 -
Heat Inductor
1 × $1,622.50 -
Blanking Plate, Heater Tap Outlet
1 × $12.10 -
Thermostat Housing
2 × $24.20 -
Cylinder Head Stud, Short
1 × $13.00 -
Exhaust Manifold Gasket
2 × $14.85 -
Blanking Plug, Various Uses
1 × $4.24 -
Wheel Nut & Washer, Suit Mini Spares Wheels
1 × $7.15 -
Bush Kit, Lower Control Arm to Subframe, Competition
2 × $46.20 -
Diesel Injector Extractor - for JLR 2.7, 3.6 engines
2 × $217.25 -
Gasket, Cylinder Head, Standard
1 × $16.50 -
Master Cylinder Tank, Plastic
2 × $44.00 -
BRAKE WEAR SENSOR, REAR - D3/D4/RRS
2 × $16.72 -
Crankshaft Speed/Position Sensor XJ40/ XJ6/ XJR
1 × $159.50 -
Thermostat Housing Stud 48mm (1.9375") Long
2 × $2.82 -
Side Panel Rear Quarter Left Hand, UK Mini
1 × $544.50 -
Valve Guide
2 × $7.70 -
Idler Pulley Primary Drive
1 × $37.13 -
HT Lead Ignition Spark Tester
1 × $49.50 -
Adjustable Suspension Height Kit, Front, Ripspeed Type
2 × $183.70 -
Clip, Interior Trim
2 × $2.86 -
Chrome Window Winder Handle
2 × $29.65 -
Wiper Blade Assembly, 10'', Mini / MGB / Triumph / Land Rover
1 × $26.68 -
Temperature Transmitter
1 × $16.50 -
Rocker Arm Bush
1 × $7.15 -
Bolt - Clutch Diaphragm to Flywheel
1 × $7.70 -
Bolt - Steering Arm to Swivel Hub
2 × $8.80 -
Heater Tap & Blanking Plate Gasket
1 × $0.66 -
Pipe Bender 3-in-1
1 × $60.50 -
BRAKE FLUID TESTER
1 × $55.00 -
Cylinder Head Nut, Plain
1 × $2.81 -
Bearing, First Motion Shaft, MGB 3 Synchro
1 × $44.00 -
Steering Rack Bush, Used On UK Rack
1 × $14.44
Steering
-
-
$14.44
Steering Rack Bush, Used On UK Rack, Made By Cam Gears
Nylon Bush for original CAM Steering Racks as fitted by Leyland/Rover
-
$0.77
Steering Rack Damper End Gasket
The same end as the Wave Washer # CCA45 is fitted
-
$0.66
Steering Rack Gasket, Damper End
The same end as the Wave Washer # CCA45 is fitted
-
$38.50
Steering Rack Pinion Bearing
Inside Steering Rack
-
$1.65
Steering Rack Wave Washer
This is a steering rack pinion wave washer, there are two of these that hold a preset tension against your pinion (load). If one of these are broken, it can make the steering a bit loose.
Please note these only fit the original steering rack (not the new UK ones).
-
-
-
Availability: This product is currently out of stock.
Tie Rod End, Steering Rack, Competition
With grease nipple, Longer track rod end for when running with negative camber, an extra 5mm of adjustment approximately over the standard item.
Sold Individually
-